caixiang
/
PX4-Autopilot
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
2 Commits
1 Branch
0 Tags
502 MiB
 
 
 
 
 
 
Tree: 624f9b2981
Branches Tags
${ item.name }
Create tag ${ searchTerm }
Create branch ${ searchTerm }
from '624f9b2981'
${ noResults }
PX4-Autopilot/boards/nxp/tropic-community/nuttx-config/include/board.h

391 lines
17 KiB
Raw Blame History

/************************************************************************************
* nuttx-configs/nxp/nxp_tropic-community/include/board.h
*
* Copyright (C) 2018 Gregory Nutt. All rights reserved.
* Authors: Gregory Nutt <gnutt@nuttx.org>
* David Sidrane <david_s5@nscdg.com>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __NUTTX_CONFIG_NXP_TROPIC_INCLUDE_BOARD_H
#define __NUTTX_CONFIG_NXP_TROPIC_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* Set VDD_SOC to 1.25V */
#define IMXRT_VDD_SOC (0x12)
/* Set Arm PLL (PLL1) to fOut = (24Mhz * ARM_PLL_DIV_SELECT/2) / ARM_PODF_DIVISOR
* 576Mhz = (24Mhz * ARM_PLL_DIV_SELECT/2) / ARM_PODF_DIVISOR
* ARM_PLL_DIV_SELECT = 96
* ARM_PODF_DIVISOR = 2
* 576Mhz = (24Mhz * 96/2) / 2
*
* AHB_CLOCK_ROOT = PLL1fOut / IMXRT_AHB_PODF_DIVIDER
* 1Hz to 600 Mhz = 576Mhz / IMXRT_ARM_CLOCK_DIVIDER
* IMXRT_ARM_CLOCK_DIVIDER = 1
* 576Mhz = 576Mhz / 1
*
* PRE_PERIPH_CLK_SEL = PRE_PERIPH_CLK_SEL_PLL1
* PERIPH_CLK_SEL = 1 (0 select PERIPH_CLK2_PODF, 1 select PRE_PERIPH_CLK_SEL_PLL1)
* PERIPH_CLK = 576Mhz
*
* IPG_CLOCK_ROOT = AHB_CLOCK_ROOT / IMXRT_IPG_PODF_DIVIDER
* IMXRT_IPG_PODF_DIVIDER = 4
* 144Mhz = 576Mhz / 4
*
* PRECLK_CLOCK_ROOT = IPG_CLOCK_ROOT / IMXRT_PERCLK_PODF_DIVIDER
* IMXRT_PERCLK_PODF_DIVIDER = 1
* 16Mhz = 144Mhz / 9
*
* SEMC_CLK_ROOT = 576Mhz / IMXRT_SEMC_PODF_DIVIDER (labeled AIX_PODF in 18.2)
* IMXRT_SEMC_PODF_DIVIDER = 8
* 72Mhz = 576Mhz / 8
*
* Set Sys PLL (PLL2) to fOut = (24Mhz * (20+(2*(DIV_SELECT)))
* 528Mhz = (24Mhz * (20+(2*(1)))
*
* Set USB1 PLL (PLL3) to fOut = (24Mhz * 20)
* 480Mhz = (24Mhz * 20)
*
* Set LPSPI PLL3 PFD0 to fOut = (480Mhz / 12 * 18)
* 720Mhz = (480Mhz / 12 * 18)
* 90Mhz = (720Mhz / LSPI_PODF_DIVIDER)
*
* Set LPI2C PLL3 / 8 to fOut = (480Mhz / 8)
* 60Mhz = (480Mhz / 8)
* 12Mhz = (60Mhz / LSPI_PODF_DIVIDER)
*
* Set USDHC1 PLL2 PFD2 to fOut = (528Mhz / 24 * 18)
* 396Mhz = (528Mhz / 24 * 18)
* 198Mhz = (396Mhz / IMXRT_USDHC1_PODF_DIVIDER)
*/
#define BOARD_XTAL_FREQUENCY 24000000
#define IMXRT_PRE_PERIPH_CLK_SEL CCM_CBCMR_PRE_PERIPH_CLK_SEL_PLL1
#define IMXRT_PERIPH_CLK_SEL CCM_CBCDR_PERIPH_CLK_SEL_PRE_PERIPH
#define IMXRT_ARM_PLL_DIV_SELECT 96
#define IMXRT_ARM_PODF_DIVIDER 2
#define IMXRT_AHB_PODF_DIVIDER 1
#define IMXRT_IPG_PODF_DIVIDER 4
#define IMXRT_PERCLK_CLK_SEL CCM_CSCMR1_PERCLK_CLK_SEL_IPG_CLK_ROOT
#define IMXRT_PERCLK_PODF_DIVIDER 9
#define IMXRT_SEMC_PODF_DIVIDER 8
#define IMXRT_CAN_CLK_SELECT CCM_CSCMR2_CAN_CLK_SEL_PLL3_SW_80
#define IMXRT_CAN_PODF_DIVIDER 1
#define IMXRT_LPSPI_CLK_SELECT CCM_CBCMR_LPSPI_CLK_SEL_PLL3_PFD0
#define IMXRT_LSPI_PODF_DIVIDER 8
#define IMXRT_LPI2C_CLK_SELECT CCM_CSCDR2_LPI2C_CLK_SEL_PLL3_60M
#define IMXRT_LSI2C_PODF_DIVIDER 5
#define IMXRT_USDHC1_CLK_SELECT CCM_CSCMR1_USDHC1_CLK_SEL_PLL2_PFD0
#define IMXRT_USDHC1_PODF_DIVIDER 2
#define IMXRT_USB1_PLL_DIV_SELECT CCM_ANALOG_PLL_USB1_DIV_SELECT_20
#define IMXRT_SYS_PLL_SELECT CCM_ANALOG_PLL_SYS_DIV_SELECT_22
#define IMXRT_USB1_PLL_DIV_SELECT CCM_ANALOG_PLL_USB1_DIV_SELECT_20
#define BOARD_CPU_FREQUENCY \
(BOARD_XTAL_FREQUENCY * (IMXRT_ARM_PLL_DIV_SELECT / 2)) / IMXRT_ARM_PODF_DIVIDER
#define BOARD_GPT_FREQUENCY \
(BOARD_CPU_FREQUENCY / IMXRT_IPG_PODF_DIVIDER) / IMXRT_PERCLK_PODF_DIVIDER
/* 108Mhz clock for FlexIO using PLL3 PFD2 @ 520 */
#define CONFIG_FLEXIO1_CLK 1
#define CONFIG_FLEXIO1_PRED_DIVIDER 5
#define CONFIG_FLEXIO1_PODF_DIVIDER 1
#define CONFIG_PLL3_PFD2_FRAC 16
#define BOARD_FLEXIO_PREQ 108000000
/* Define this to enable tracing */
#if CONFIG_USE_TRACE
# define IMXRT_TRACE_PODF_DIVIDER 1
# define IMXRT_TRACE_CLK_SELECT CCM_CBCMR_TRACE_CLK_SEL_PLL2_PFD0
#endif
/* SDIO *****************************************************************************/
/* Pin drive characteristics */
#define USDHC1_DATAX_IOMUX (IOMUX_SLEW_FAST | IOMUX_DRIVE_130OHM | IOMUX_PULL_UP_47K | IOMUX_SCHMITT_TRIGGER)
#define USDHC1_CMD_IOMUX (IOMUX_SLEW_FAST | IOMUX_DRIVE_130OHM | IOMUX_PULL_UP_47K | IOMUX_SCHMITT_TRIGGER)
#define USDHC1_CLK_IOMUX (IOMUX_SLEW_FAST | IOMUX_DRIVE_130OHM | IOMUX_SPEED_MAX)
#define USDHC1_CD_IOMUX (IOMUX_PULL_UP_47K | IOMUX_SCHMITT_TRIGGER)
#define PIN_USDHC1_D0 (GPIO_USDHC1_DATA0_1 | USDHC1_DATAX_IOMUX) /* GPIO_SD_B0_02 */
#define PIN_USDHC1_D1 (GPIO_USDHC1_DATA1_1 | USDHC1_DATAX_IOMUX) /* GPIO_SD_B0_03 */
#define PIN_USDHC1_D2 (GPIO_USDHC1_DATA2_1 | USDHC1_DATAX_IOMUX) /* GPIO_SD_B0_04 */
#define PIN_USDHC1_D3 (GPIO_USDHC1_DATA3_1 | USDHC1_DATAX_IOMUX) /* GPIO_SD_B0_05 */
#define PIN_USDHC1_DCLK (GPIO_USDHC1_CLK_1 | USDHC1_CLK_IOMUX) /* GPIO_SD_B0_01 */
#define PIN_USDHC1_CMD (GPIO_USDHC1_CMD_1 | USDHC1_CMD_IOMUX) /* GPIO_SD_B0_00 */
#define PIN_USDHC1_CD (PIN_USDHC1_D3)
/* Ideal 400Khz for initial inquiry.
* Given input clock 198 Mhz.
* 386.71875 KHz = 198 Mhz / (256 * 2)
*/
#define BOARD_USDHC_IDMODE_PRESCALER USDHC_SYSCTL_SDCLKFS_DIV256
#define BOARD_USDHC_IDMODE_DIVISOR USDHC_SYSCTL_DVS_DIV(2)
/* Ideal 25 Mhz for other modes
* Given input clock 198 Mhz.
* 24.75 MHz = 198 Mhz / (8 * 1)
*/
#define BOARD_USDHC_MMCMODE_PRESCALER USDHC_SYSCTL_SDCLKFS_DIV8
#define BOARD_USDHC_MMCMODE_DIVISOR USDHC_SYSCTL_DVS_DIV(1)
#define BOARD_USDHC_SD1MODE_PRESCALER USDHC_SYSCTL_SDCLKFS_DIV8
#define BOARD_USDHC_SD1MODE_DIVISOR USDHC_SYSCTL_DVS_DIV(1)
#define BOARD_USDHC_SD4MODE_PRESCALER USDHC_SYSCTL_SDCLKFS_DIV8
#define BOARD_USDHC_SD4MODE_DIVISOR USDHC_SYSCTL_DVS_DIV(1)
/* ETH Disambiguation *******************************************************/
/* Ethernet Interrupt: GPIO_B0_15
*
* This pin has a week pull-up within the PHY, is open-drain, and requires
* an external 1k ohm pull-up resistor (present on the EVK). A falling
* edge then indicates a change in state of the PHY.
*/
#define GPIO_ENET_INT (IOMUX_ENET_INT_DEFAULT | \
GPIO_PORT2 | GPIO_PIN15) /* B0_15 */
#define GPIO_ENET_IRQ IMXRT_IRQ_GPIO2_15
/* Ethernet Reset: GPIO_B0_14
*
* The #RST uses inverted logic. The initial value of zero will put the
* PHY into the reset state.
*/
#define GPIO_ENET_RST (GPIO_OUTPUT | GPIO_OUTPUT_ZERO | \
GPIO_PORT2 | GPIO_PIN14 | IOMUX_ENET_RST_DEFAULT) /* B0_14 */
#define GPIO_ENET_TX_DATA00 (GPIO_ENET_TX_DATA00_1| \
IOMUX_ENET_DATA_DEFAULT) /* GPIO_B1_07 */
#define GPIO_ENET_TX_DATA01 (GPIO_ENET_TX_DATA01_1| \
IOMUX_ENET_DATA_DEFAULT) /* GPIO_B1_08 */
#define GPIO_ENET_RX_DATA00 (GPIO_ENET_RX_DATA00_1| \
IOMUX_ENET_DATA_DEFAULT) /* GPIO_B1_04 */
#define GPIO_ENET_RX_DATA01 (GPIO_ENET_RX_DATA01_1| \
IOMUX_ENET_DATA_DEFAULT) /* GPIO_B1_05 */
#define GPIO_ENET_MDIO (GPIO_ENET_MDIO_1|IOMUX_ENET_MDIO_DEFAULT) /* GPIO_B1_15 */
#define GPIO_ENET_MDC (GPIO_ENET_MDC_1|IOMUX_ENET_MDC_DEFAULT) /* GPIO_B1_14 */
#define GPIO_ENET_RX_EN (GPIO_ENET_RX_EN_1|IOMUX_ENET_EN_DEFAULT) /* GPIO_B1_06 */
#define GPIO_ENET_RX_ER (GPIO_ENET_RX_ER_1|IOMUX_ENET_RXERR_DEFAULT) /* GPIO_B1_11 */
#define GPIO_ENET_TX_CLK (GPIO_ENET_REF_CLK_2|\
IOMUX_ENET_TX_CLK_DEFAULT) /* GPIO_B1_10 */
#define GPIO_ENET_TX_EN (GPIO_ENET_TX_EN_1|IOMUX_ENET_EN_DEFAULT) /* GPIO_B1_09 */
/* LED definitions ******************************************************************/
/* The nxp fmutr1062 board has numerous LEDs but only three, LED_GREEN a Green LED,
* LED_BLUE a Blue LED and LED_RED a Red LED, that can be controlled by software.
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
* The following definitions are used to access individual LEDs.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED1 0
#define BOARD_LED2 1
#define BOARD_LED3 2
#define BOARD_NLEDS 3
#define BOARD_LED_RED BOARD_LED1
#define BOARD_LED_GREEN BOARD_LED2
#define BOARD_LED_BLUE BOARD_LED3
/* LED bits for use with board_userled_all() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
#define BOARD_LED2_BIT (1 << BOARD_LED2)
#define BOARD_LED3_BIT (1 << BOARD_LED3)
/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
* include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
*
* SYMBOL Meaning LED state
* Red Green Blue
* ---------------------- -------------------------- ------ ------ ----*/
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 1 /* Heap has been allocated OFF OFF ON */
#define LED_IRQSENABLED 2 /* Interrupts enabled OFF ON OFF */
#define LED_STACKCREATED 3 /* Idle stack created OFF ON ON */
#define LED_INIRQ 4 /* In an interrupt N/C N/C GLOW */
#define LED_SIGNAL 5 /* In a signal handler N/C GLOW N/C */
#define LED_ASSERTION 6 /* An assertion failed GLOW N/C GLOW */
#define LED_PANIC 7 /* The system has crashed Blink OFF N/C */
#define LED_IDLE 8 /* MCU is is sleep mode ON OFF OFF */
/* Thus if the Green LED is statically on, NuttX has successfully booted and
* is, apparently, running normally. If the Red LED is flashing at
* approximately 2Hz, then a fatal error has been detected and the system
* has halted.
*/
/* PIO Disambiguation ***************************************************************/
/* LPUARTs
*/
#define LPUART_IOMUX (IOMUX_PULL_UP_22K | IOMUX_DRIVE_40OHM | IOMUX_SLEW_SLOW | IOMUX_SPEED_LOW | IOMUX_SCHMITT_TRIGGER)
#define IOMUX_UART_CTS_DEFAULT (IOMUX_PULL_DOWN_100K | IOMUX_DRIVE_40OHM | IOMUX_SLEW_SLOW)
/* Debug */
#define GPIO_LPUART5_RX (GPIO_LPUART5_RX_1 | LPUART_IOMUX) /* GPIO_B1_13 */
#define GPIO_LPUART5_TX (GPIO_LPUART5_TX_1 | LPUART_IOMUX) /* GPIO_B1_12 */
/* AUX */
#define GPIO_LPUART4_RX (GPIO_LPUART4_RX_3 | LPUART_IOMUX) /* GPIO_B1_01 */
#define GPIO_LPUART4_TX (GPIO_LPUART4_TX_3 | LPUART_IOMUX) /* GPIO_B1_00 */
/* GPS 1 */
#define GPIO_LPUART2_RX (GPIO_LPUART2_RX_1 | LPUART_IOMUX) /* GPIO_AD_B1_03 */
#define GPIO_LPUART2_TX (GPIO_LPUART2_TX_1 | LPUART_IOMUX) /* GPIO_AD_B1_02 */
/* Telem 1 */
#define HS_INPUT_IOMUX (IOMUX_CMOS_INPUT | IOMUX_SLEW_SLOW | IOMUX_DRIVE_HIZ | IOMUX_SPEED_MEDIUM | IOMUX_PULL_UP_47K)
#define HS_OUTPUT_IOMUX (IOMUX_CMOS_OUTPUT | IOMUX_SLEW_FAST | IOMUX_DRIVE_33OHM | IOMUX_SPEED_MEDIUM | IOMUX_PULL_KEEP)
#define GPIO_LPUART3_RX (GPIO_LPUART3_RX_1 | LPUART_IOMUX) /* GPIO_AD_B1_07 */
#define GPIO_LPUART3_TX (GPIO_LPUART3_TX_1 | LPUART_IOMUX) /* GPIO_AD_B1_06 */
#define GPIO_LPUART3_CTS (GPIO_LPUART3_CTS_1 | IOMUX_UART_CTS_DEFAULT | PADMUX_SION) /* GPIO_AD_B1_04 GPIO1_IO20 (GPIO only, no HW Flow control) */
#define GPIO_LPUART3_RTS (GPIO_PORT1 | GPIO_PIN21 | GPIO_OUTPUT | GPIO_OUTPUT_ZERO | HS_OUTPUT_IOMUX) /* GPIO_AD_B1_05 GPIO1_IO21 (GPIO only, no HW Flow control) */
//TODO check RT7 partial HW handshake
/* RC INPUT single wire mode on TX, RX is not used */
#define GPIO_LPUART8_RX (GPIO_LPUART8_RX_2 | LPUART_IOMUX) /* WRONG!! */
#define GPIO_LPUART8_TX (GPIO_LPUART8_TX_1 | LPUART_IOMUX) /* GPIO_AD_B1_10 */
/* CAN
*
* CAN1 is routed to transceiver.
* CAN2 is routed to transceiver.
* CAN3 is routed to transceiver.
*/
#define FLEXCAN_IOMUX (IOMUX_PULL_UP_100K | IOMUX_DRIVE_40OHM | IOMUX_SLEW_FAST | IOMUX_SPEED_MEDIUM)
#define GPIO_FLEXCAN3_RX (GPIO_FLEXCAN3_RX_3 | FLEXCAN_IOMUX) /* GPIO_EMC_37 */
#define GPIO_FLEXCAN3_TX (GPIO_FLEXCAN3_TX_3 | FLEXCAN_IOMUX) /* GPIO_EMC_36 */
/* LPSPI */
#define LPSPI_IOMUX (IOMUX_PULL_UP_100K | IOMUX_DRIVE_33OHM | IOMUX_SLEW_FAST | IOMUX_SPEED_MAX)
#define GPIO_LPSPI3_SCK (GPIO_LPSPI3_SCK_1 | LPSPI_IOMUX) /* GPIO_AD_B1_15 */
#define GPIO_LPSPI3_MISO (GPIO_LPSPI3_SDI_1 | LPSPI_IOMUX) /* GPIO_AD_B1_13 */
#define GPIO_LPSPI3_MOSI (GPIO_LPSPI3_SDO_1 | LPSPI_IOMUX) /* GPIO_AD_B1_14 */
#define GPIO_LPSPI4_SCK (GPIO_LPSPI4_SCK_2 | LPSPI_IOMUX) /* GPIO_B0_03 */
#define GPIO_LPSPI4_MISO (GPIO_LPSPI4_SDI_2 | LPSPI_IOMUX) /* GPIO_B0_01 */
#define GPIO_LPSPI4_MOSI (GPIO_LPSPI4_SDO_2 | LPSPI_IOMUX) /* GPIO_B0_02 */
#define BOARD_SPI_BUS_MAX_BUS_ITEMS 2
/* LPI2Cs */
#define LPI2C_IOMUX (IOMUX_SPEED_MEDIUM | IOMUX_DRIVE_33OHM | IOMUX_OPENDRAIN | GPIO_SION_ENABLE)
#define LPI2C_IO_IOMUX (IOMUX_SPEED_MAX | IOMUX_SLEW_FAST | IOMUX_DRIVE_33OHM | IOMUX_OPENDRAIN | IOMUX_PULL_NONE)
#define GPIO_LPI2C1_SDA (GPIO_LPI2C1_SDA_2 | LPI2C_IOMUX) /* EVK J24-9 R276 */ /* GPIO_AD_B1_01 */
#define GPIO_LPI2C1_SCL (GPIO_LPI2C1_SCL_2 | LPI2C_IOMUX) /* EVK J24-10 R277 */ /* GPIO_AD_B1_00 */
#define GPIO_LPI2C1_SDA_RESET (GPIO_PORT1 | GPIO_PIN17 | GPIO_OUTPUT | GPIO_OUTPUT_ONE | LPI2C_IO_IOMUX) /* GPIO_AD_B1_01 GPIO1_IO17 */
#define GPIO_LPI2C1_SCL_RESET (GPIO_PORT1 | GPIO_PIN16 | GPIO_OUTPUT | GPIO_OUTPUT_ONE | LPI2C_IO_IOMUX) /* GPIO_AD_B1_00 GPIO1_IO16 */
#define GPIO_LPI2C4_SDA (GPIO_LPI2C4_SDA_1 | LPI2C_IOMUX) /* GPIO_AD_B0_13 */
#define GPIO_LPI2C4_SCL (GPIO_LPI2C4_SCL_1 | LPI2C_IOMUX) /* GPIO_AD_B0_12 */
#define GPIO_LPI2C4_SDA_RESET (GPIO_PORT1 | GPIO_PIN13 | GPIO_OUTPUT | GPIO_OUTPUT_ONE | LPI2C_IO_IOMUX) /* GPIO_AD_B0_13 */
#define GPIO_LPI2C4_SCL_RESET (GPIO_PORT1 | GPIO_PIN12 | GPIO_OUTPUT | GPIO_OUTPUT_ONE | LPI2C_IO_IOMUX) /* GPIO_AD_B0_12 */
/* Board doesn't provide GPIO or other Hardware for signaling to timing analyzer */
#define PROBE_INIT(mask)
#define PROBE(n,s)
#define PROBE_MARK(n)
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Functions
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __NUTTX_CONFIG_NXP_TROPIC_INCLUDE_BOARD_H */