#!/bin/sh
#
# @name UVify IFO
#
# @type Quadrotor x
# @class Copter
#
# @maintainer Hyon Lim <lim@uvify.com>
#
# @board px4_fmu-v2 exclude
# @board px4_fmu-v3 exclude
# @board px4_fmu-v4pro exclude
# @board px4_fmu-v5 exclude
# @board px4_fmu-v5x exclude
# @board auterion_fmu-v6x exclude
# @board px4_fmu-v6x exclude
# @board bitcraze_crazyflie exclude
# @board cuav_x7pro exclude
#

. ${R}etc/init.d/rc.mc_defaults

# Attitude & rate gains
param set-default MC_ROLLRATE_D 0.0013
param set-default MC_PITCHRATE_D 0.0016

param set-default MPC_MANTHR_MAX 0.9

# Filter settings
param set-default IMU_DGYRO_CUTOFF 90
param set-default IMU_GYRO_CUTOFF 100

# System
param set-default SENS_BOARD_ROT 10

# EKF2
param set-default EKF2_GND_EFF_DZ 6

# Position control
param set-default MPC_Z_VEL_I_ACC 0.4

param set-default MPC_THR_MIN 0.06
param set-default MPC_THR_HOVER 0.3

param set-default MIS_TAKEOFF_ALT 1.1
param set-default MPC_XY_P 1.7
param set-default MPC_XY_VEL_P_ACC 2.6
param set-default MPC_XY_VEL_I_ACC 1.2
param set-default MPC_TKO_RAMP_T 1
param set-default MPC_VEL_MANUAL 3

param set-default BAT1_SOURCE 0
param set-default BAT1_N_CELLS 4
param set-default BAT1_V_DIV 10.14
param set-default BAT1_A_PER_V 18.18

# Filter settings
param set-default IMU_GYRO_CUTOFF 90
param set-default IMU_DGYRO_CUTOFF 70

# Don't try to be intelligent on RC loss: just cut the motors
param set-default NAV_RCL_ACT 6

# TELEM1 ttyS1 - Wifi module
param set-default MAV_0_CONFIG 101
param set-default MAV_0_RATE 0
# onboard
param set-default MAV_0_MODE 2
param set-default SER_TEL1_BAUD 921600

# TELEM2 ttyS2 - Sub 1-Ghz
param set-default MAV_1_CONFIG 102
# normal
param set-default MAV_1_MODE 0
param set-default SER_TEL2_BAUD 57600

param set-default PWM_MAIN_TIM0 0

# Square quadrotor X PX4 numbering
param set-default CA_ROTOR_COUNT 4
param set-default CA_ROTOR0_PX 1
param set-default CA_ROTOR0_PY 1
param set-default CA_ROTOR1_PX -1
param set-default CA_ROTOR1_PY -1
param set-default CA_ROTOR2_PX 1
param set-default CA_ROTOR2_PY -1
param set-default CA_ROTOR2_KM -0.05
param set-default CA_ROTOR3_PX -1
param set-default CA_ROTOR3_PY 1
param set-default CA_ROTOR3_KM -0.05

param set-default PWM_MAIN_FUNC1 101
param set-default PWM_MAIN_FUNC2 102
param set-default PWM_MAIN_FUNC3 103
param set-default PWM_MAIN_FUNC4 104